Big Gulp Dust Hood

Item #: DBGULP
$15.95
Reg. Price: $27.95
You Save: $12.00
Quantity:
In Stock Ready to Ship
Shipping Charge: $8 shipping for ground service

Rating 5 out of 55 out of 55 out of 55 out of 55 out of 5

Description Specifications Shipping Reviews and Awards
The HUGE 13" x 16" opening on this new hood makes it ideal for collecting dust from problem machines. Ideal for: •Mitre Saws • Lathes • Radial Arm Saws • Carving • Sanding • Planers without hoods. Its lightweight and portable and easy to position anywhere
Type: Plastic
Size Inlet x Outlet(s) - dia: 4" to 13" x 16"
Category: Specialty Machine Dust Hoods
  • Package Weight: 2.00 pounds
  • Shipping Charge: $8 shipping for ground service
  • Packing: Item is shipped in its own box.

Note: Above shipping policies apply to Continental US only. We will call or email to advise you of shipping policies to other locations.

Average Customer Review: 5 out of 55 out of 55 out of 55 out of 55 out of 5 8 Reviews

Write an online review and share your thoughts with others.

5 out of 55 out of 55 out of 55 out of 55 out of 5 The Bigger the Gulp, the Better
Reviewer: Norman Dresner (Severn, MD)
Submitted: 6.19.2010

On the lathe, when sanding any wood or turning dry wood, small particles of wood are spewn everywhere, ending up either in my lungs or on surfaces all over the house. It's vital for health -- and really helpful for marital bliss -- to keep this dust under control. That's where an adequate dust collection system comes in. BUT the only way to get ALL of the dust produced on the lathe is to have an aperture in the system that's close enough and big enough to span the dust-producing area. That's were the Big Gulp shines! It's huge -- at least compared to normal tool accessories -- so it can gather almost every particle of dust produced and put it in the collection system where it belongs. Yes, it could be bigger -- I'd like that's about the same height and twice the length, but for now this is the biggest and best collector front end available!

4 out of 54 out of 54 out of 54 out of 54 out of 5 The best hood so far for miter saws
Reviewer: Philip Hookham (Bell Canyon, CA)
Submitted: 12.21.2009

I've tried many possible solutions to collecting dust from my miter saw, from home made rigs to using the built-in dust collection port in the saw (DeWalt 12"). This is the best solution so far. It collects most of the dust, especially the finer stuff, when coupled with my 1 1/2 hp Penn State Industries dust collector. Verical and horizontal positioning are important for optimal dust collection.

5 out of 55 out of 55 out of 55 out of 55 out of 5 Excellent Value
Reviewer: James Davis (Hammond, LA)
Submitted: 10.27.2009

It does the job for which it was intended. Quality and price was better than the competition.

4 out of 54 out of 54 out of 54 out of 54 out of 5 Maybe the best miter saw dust colector I've found
Reviewer: Tom Griffith (Austin, TX)
Submitted: 9.1.2009

I have searched for a suitable dust collector for a miter saw, and I have built a couple, none of which worked well. The Big Gulp, with a couple of "wings" attached to each side, seems to come as close to doing the job as I've come up with so far. Some sawdust still escapes around it, but it's much better than anything else I've come up with.

5 out of 55 out of 55 out of 55 out of 55 out of 5 Big Gulp Dust Hood
Reviewer: Jerry Garretson (Las Vegas, NV)
Submitted: 7.7.2009

I really like the dust hood that I purchased. It saves a lot of mess and leaves little saw dust behind.

View all 8 reviews

LEARNING CENTER

Online prices and selection generally match our online catalog, but may vary.
Prices and offers are subject to change.
© Penn State Industries
All Rights Reserved.